TECHNICAL DOCUMENTATIONTPI Q-Proof Bitumen
Liquid elastic bitumen-based waterproofing membrane
DESCRIPTION OF TPI Q-Proof Bitumen
It is an advanced water-based, one-component, liquid, cold-applied polymer bitumen waterproofing compound.
TPI Q-Proof Bitumen Application
Suitable for waterproofing various locations in a construction project, such as:
- Underground waterproofing layer for concrete and plaster surfaces.
- Flat roof. Balcony.
- Basement.
- Retaining wall.
ADVANTAGE
- Easy to apply with a brush or spray.
- The waterproofing membrane has high elasticity.
- Excellent bonding properties and ability to seal cracks.
- Designed for use on both old and new structures.
- Contains no solvents.
- Odorless and non-sticky.
SPECIFICATIONS
| Target | TPI Q-Proof Bitumen |
| Ingredient | Polymer bitumen emulsion |
| Shape/Color | Dark brown solution |
| Finish color | Black when dry |
| Proportion | 1.10 ± 0.10 kg/liter |
| Coating system | 1 primer coat and 2 top coats |
| Standard | Lining layer: 0.2 – 0.3kg ⁄ m2(*)
Coating: ~0.6kg/m2/layer(*) Approximately 2kg/m² will yield a waterproofing membrane with a thickness of 1.1mm after drying. |
| Drying time | Surface drying time: 60 minutes.
Completely dry in approximately 4 hours. |
| Specifications | 4.5kg & 20kg boxes |
| Expiry | 12 months (when unopened) |
| Storage | The packaging must be intact, unopened, and undamaged.
Store in a cool, dry, shaded place at a temperature of 5°C or higher.oC to 35oC. |
(*) Depending on the surface and application technique.
INSTRUCTIONS FOR USE
Surface preparation
- The surface must be thoroughly cleaned of dust and grease before waterproofing.
- Repair any cracks or defects on the concrete or cement surface before applying waterproofing.
Applying the primer layer
- Add approximately 20-50% of clean water (by weight) to TPI Q-Proof Bitumen and mix well. Apply the primer coat to the surface using a brush, roller, or spray gun. The recommended application rate is 0.2 – 0.3 kg/m2. Allow this primer layer to dry completely before applying subsequent layers.
- In the case of porous and highly permeable substrates, the surface must be moistened before application. Avoid standing water.
Product manufacturing
- Construction TPI Q-Proof Bitumen Apply to a clean, primed surface using a brush, roller, or spray gun. When spraying onto exterior walls below ground level, ensure the surface is covered with a thick, even layer and free of air bubbles.
- For waterproofing, 2-3 layers should be applied.
- Wait for each layer to dry completely before applying the next.
Notes on construction
All right-angled edges must have mortar applied to the corners to create a slope of at least 25x25mm before construction. All edges, protrusions, and depressions must be treated before construction. TPI Q-Proof Bitumen Extend 50-100mm along both edges of the part. These treated areas need to dry overnight before applying the membrane.
- In key or necessary areas, TPI Q-Proof Bitumen It can be reinforced by using a suitable fiberglass mesh.
- Do TPI Q-Proof Bitumen Exposed surfaces are not resistant to ultraviolet radiation over long periods. (For flat roofs) a protective plaster layer of 15-20mm thick must be applied immediately after construction. This plaster layer should be mixed with additional mortar. TPI Latex proportionally 5 liters TPI Latex for 1 cubic meter of cement mortar.
Toilet
- Clean the equipment and tools before use. TPI Q-Proof Bitumen Once dry, rinse with clean water.
- After TPI Q-Proof Bitumen Once it has hardened, it can only be cleaned by mechanical means.
HEALTH AND SAFETY INFORMATION
Occupational safety and health: Appropriate personal protective equipment, including safety glasses and gloves, must be worn when using this product.
Ecology: Do not dispose of into water sources or soil.
Transport: Not dangerous.
Refer to the product's Material Safety Data Sheet (MSDS) and other relevant safety data sheets.
Reviews
There are no reviews yet.