TPI Q-PROOF 828 (2.6:1) – Fiber-reinforced waterproofing mortar

TPI Q-Proof 828 (2.6:1)
Elastic waterproofing and protective mortar with fiber reinforcement

DESCRIPTION TPI Q-PROOF 828

As a two-component, fiber-reinforced, cement-based waterproofing coating with good crack-filling capabilities, this product is applied to concrete or mortar surfaces to prevent water ingress.

Uses of TPI Q-PROOF 828

• Waterproofing and elastic protection for water-retaining or water-contacting structures such as tanks, concrete pipes, bridges, etc.
• The coating protects against the carbonation of concrete surfaces.
• Waterproof bathrooms, wet areas, drying yards, balconies, and swimming pools before installing ceramic tiles using cement-based tile adhesive.
• Waterproofing and protecting concrete structures. Waterproofing for areas inside retaining walls or concrete floors where water pressure is low.

Advantages of TPI Q-Proof 828

• Easy to mix and easy to apply with a roller or brush.
• It adheres well to solid surfaces.
• Non-toxic, just like cement.
• Economic efficiency.
• Meets BS EN 14891 standards.
• Enhanced with REINFORCING FIBERS, it provides better crack sealing capabilities even at lower application rates.
• With its versatile applications, the product can be used for waterproofing bathrooms, balconies, swimming pools, water tanks, etc.
• Suitable for drinking water tanks.

SPECIFICATIONS

Target	TPI Q-Proof 828
Type / Color	Part A: Milky white solution Part B: Gray Powder
Proportion	Mixture A+B: ~ 1.6 – 1.8 kg/liter
Specifications	Set: 18kg (A 5kg + B 13kg) Set: 36kg (A 10kg + B 26kg)
Mixing ratio	Part A : B = 1 : 2.6 (by mass)
Waterproofing rating	1.0 kg/m2/layer	Apply a minimum of 2 layers.
		Apply three layers in areas with high water levels.
Create a crack bridge.	> 0.75 mm
Adhesion	> 0.5 Mpa (*)
Waterproofing	Meets BS EN 14891 standards. (Water pressure of 1.5 bar for 7 days)
Construction temperature	8 – 40oC
Construction time	30 minutes (at 27)oC)
Expiry	12 months in unopened packaging.
Storage	A cool, dry, shady place.

(*) 28 days old, on a prepared and moistened concrete surface.

PRODUCT INSTALLATION INSTRUCTIONS

Prepare the construction surface.

• Concrete and mortar surfaces must be clean and free of grease and other loose particles.
• For metal surfaces, they must be clean and free of rust., ^. It's greasy.
• Absorbent surfaces must be moistened to saturation with clean water (but without standing water) before applying the coating. TPI Q-Proof 828 the first.
• The minimum surface temperature is 8°C.^oC and a maximum of 40^oC.

Mix the products

• Prepare a clean container and a mixer. Pour Part A (the solution) into the container first, then gradually add Part B (the powder) while stirring at low speed. Mixing both components together according to the recommended ratio will form a thick paste.

Construction

• Construction of the layer TPI Q-Proof 828 First, apply to the fully saturated surface using a brush, wire brush, or trowel.
• Allow the product to cure for 1-2 hours at a temperature above 27°C before applying the second coat. Sweep away any air bubbles from the surface and apply the second coat at a 90° angle to the first coat.
• Apply the third coat only when deemed necessary or required.
• The minimum drying time for the final coat is 6-8 hours.

Maintenance of the waterproofing layer

• Like other cement-based products, curing treatment is required. TPI Q-Proof 828 Immediately after construction, avoiding direct sunlight, strong winds, and frost for 3 to 5 days is essential to ensure the material fully hydrates and minimizes small cracks.
• Use plastic sheeting for maintenance or other approved measures.

Cleaning the tools

• Clean all tools and equipment with clean water immediately after use.
• Hardened material can only be cleaned by mechanical means.

Note

• After application, allow a minimum drying time of 3 days before soaking in water.
• Always use a connecting oil reservoir. TPI Latex To prevent blistering during mortar application. Finishing/protecting layer applied over the waterproofing layer.
• Always construct a test area before starting mass production.

HEALTH AND SAFETY INFORMATION

Occupational safety and health: Appropriate personal protective equipment, including safety glasses and gloves, must be worn when using this product.

Ecology: Do not dispose of into water sources or soil.

Transport:  Not dangerous.

Dispose of waste: According to local regulations.

Important note:

TPI Q-Proof 828 May cause allergic reactions. Appropriate precautions should be taken to minimize skin contact. If the product splashes into the eyes or mucous membranes, rinse with clean water and seek medical attention immediately.