TPI Q-PROOF 901 (2:1) – High-quality, two-component waterproofing mortar

TPI Q-PROOF 901 (2:1)
High-performance, two-component, high-elasticity waterproofing and protective mortar.

DESCRIPTION OF TPI Q-PROOF 901

As a two-component, highly elastic cement-based waterproofing coating, this product is applied to concrete or mortar surfaces to prevent water ingress.

Uses of TPI Q-PROOF 901

• It is used for waterproofing, sealing hairline cracks, and also as a protective layer against carbon dioxide penetration, preventing the formation of dew spots and ice on the surface.
• This product is used for waterproofing: water tanks, basements, parking lots, rooftops, balconies, bridges, retaining walls, swimming pools, reinforced concrete drainage pipes, waterproof floors and walls, flower pots, kitchens, and waste treatment floors.

Advantages of TPI Q-PROOF 901

• Capable of filling cracks up to 1mm wide at 20°C.^oC).
• Easy to mix and easy to apply with a roller or brush.
• Good adhesion to solid surfaces. Good elasticity.
• Increased resistance to salt spray and ice formation.
• Prevents the penetration of carbon dioxide.
• Non-toxic, just like cement.
• Economic efficiency

SPECIFICATIONS

Target	TPI Q-Proof 901
Type / Color	Part A: Milky white solution Part B: Gray Powder
Proportion	Mixture A+B: ~ 1.6 – 1.8 kg/liter
Specifications	Set: 15kg (A 5kg + B 10kg) Set: 30kg (A 10kg + B 20kg)
Mixing ratio	Part A : B = 1 : 2 (by mass)
Waterproofing rating	1.0 kg/m2/layer	Apply a minimum of 2 layers.
		Apply three layers in areas with high water levels.
Create a crack bridge.	> 0.85 mm
Adhesion	> 0.8 Mpa (*)
Waterproofing	Meets BS EN 14891 standards. (Water pressure of 1.5 bar for 7 days)
Construction temperature	8 – 40oC
Construction time	30 minutes (at 27)oC)
Expiry	12 months in unopened packaging.
Storage	A cool, dry, shady place.

(*) 28 days old, on a prepared and moistened concrete surface.

PRODUCT INSTALLATION INSTRUCTIONS

Prepare the construction surface.

• Concrete and mortar surfaces must be clean and free of grease and other loose particles.
• For metal surfaces, they must be clean, free of rust, and grease.
• Absorbent surfaces must be moistened to saturation with clean water (but without standing water) before applying the first coat.
• The minimum surface temperature is 8°C.^oC and a maximum of 35^oC.

Mix the products

• Prepare a clean container and a mixer for mixing. For Part A Pour the solution into the container first, then stir at low speed while gradually adding Part B (powder).
• When both components are mixed together in the recommended ratio, they will form a thick, paste-like consistency.

Construction

• Construction of the layer TPI Q-Proof 901 First, apply to the fully saturated surface using a brush, wire brush, or trowel.
• Allow the product to freeze for 1-2 hours at a temperature above 27°C.^oApply the second coat at a 90-degree angle. Sweep away any air bubbles from the surface and apply the second coat at a 90-degree angle.^o compared to the first class.
• Apply the third coat only when deemed necessary or required.
• The minimum drying time for the final coat is 6-8 hours.

Maintenance of the waterproofing layer

• Like other cement-based products, curing treatment is required. TPI Q-Proof 901 Immediately after construction, avoiding direct sunlight, strong winds, and frost for 3 to 5 days is essential to ensure the material fully hydrates and minimizes small cracks.
• Use plastic sheeting for maintenance or other approved measures.

Cleaning the tools

• Clean all tools and equipment with clean water immediately after use.
• Hardened material can only be cleaned by mechanical means.

Note

• After application, allow a minimum drying time of 3 days before soaking in water.
• Always use a connecting oil reservoir. TPI Latex To prevent blistering when applying the finishing/protective mortar layer over the waterproofing layer.
• Always construct a test area before starting mass production.

HEALTH AND SAFETY INFORMATION

Occupational safety and health: Appropriate personal protective equipment, including safety glasses and gloves, must be worn when using this product.

Ecology: Do not dispose of into water sources or soil.

Transport:  Not dangerous.

Dispose of waste: According to local regulations.

Important note:

TPI Q-Proof 901 May cause allergic reactions. Appropriate precautions should be taken to minimize skin contact. If the product splashes into the eyes or mucous membranes, rinse with clean water and seek medical attention immediately.