TPI FS240 – Two-component, solvent-free self-leveling epoxy coating.

TPI FS240
Two-component, solvent-free self-leveling epoxy coating.

DESCRIPTION TPI FS 240

This is a two-component, solvent-free, colored epoxy resin-based paint. Upon application and complete curing, the product creates a smooth, hard coating that resists common chemicals, abrasion, and water penetration.

TPI FS 240 APPLICATION

Used as a coating for concrete and screed floors subjected to low to high loads, such as:

• Flooring for warehouses, halls, workshops, repair and maintenance areas, garages, ramps, etc.
• Coating for sandblasting systems to create a rough surface.
• Suitable for applications in water tanks, food processing plants, wastewater treatment environments, etc.

Advantages of TPI FS 240

• Easy to install.
• Non-toxic.
• Because it contains no solvents, it should only be used in restricted areas.
• It prevents liquids from penetrating through.
• High resistance to chemical corrosion, impact, and abrasion.
• The surface has a glossy finish.
• Easy to clean surface.

SPECIFICATIONS

Target	TPI FS 240
Ingredient	Liquid epoxy
Color	Part A: Plastics – colored Part B: Curing – Transparent Mixture: Gray, green…
Density	Part A: ~1.70 kg/liter Part B: ~1.05 kg/liter  Mixture: ~1.55 kg/liter
Packaging specifications	Part A: 20kg/carton Part B: 5kg / carton Part A + B: 25kg / set
Mixing ratio	5:1 (by weight)
Solid content	100%
Compressive strength	> 45 N/mm2
Adhesion strength	> 1.5 N/mm2
Expiry	24 months (when unopened)
Storage	The packaging must be intact, unopened, and undamaged. Store in a cool, dry, shaded place at a temperature of 10°C or higher.oC to 35oC.

Coating system and coverage:

Coating system	1 x primer coat: TPI Primer SB 0.2 – 0.4 kg/m²2
	2 coats: TPI FS 240 0.5 kg/m²2
Sand sprinkling system	1 x primer coat: TPI Primer SB 0.2 – 0.4 kg/m²2
	1 x coating: TPI FS 240 0.5 kg/m²2
	1 layer of sand: 0.3 – 1.2 mm, 4.0 – 5.0 kg/m²2
	1 x coating: TPI FS 240 0.5 kg/m²2
Construction temperature	10 – 30oC
Curing time	Facial treatment time: 80 – 180 minutes Between coats: 8 – 20 hours Complete curing: 7 days

INSTRUCTIONS FOR USE

Surface preparation

• The concrete surface must be solid and have a minimum compressive strength of 25 N/mm² and a minimum adhesion strength of 1.5 N/mm².
• The surface must be clean, dry, and free of contaminants such as dirt, oil, grease, old coatings, and surface maintenance compounds.
• Weak concrete and dirt must be removed. Surface defects such as pits, voids, cracks, and bumps must be treated and smoothed.

Check for moisture levels and apply the primer.

• Check surface moisture, relative humidity, and dew point before application.
• If the surface moisture content is < 4.5%, use an epoxy primer. TPI Primer SB or TPI Primer FS.
• If the surface moisture content is >= 4.5%, use a moisture-resistant epoxy primer. TPI Primer MB.

Mixing sequence

• TPI FS 240 It is supplied in a two-component kit consisting of a base component A and a curing agent B.
• Before mixing, stir ingredient A thoroughly. Once all of ingredient B has been added to ingredient A, continue mixing for 3 minutes until a homogeneous mixture is achieved.
• Do not mix for too long to reduce air entrainment.
• Use a low-speed stirrer (300-400 rpm) or other suitable mixing equipment.

Applying the coating

• Class TPI FS 240 The first coat must be applied as a base coat using a rubbing motion to ensure an even finish. The first coat must be allowed to dry for at least 8 hours at 20°C or 4 hours at 35°C.
• The maximum coating time should be adhered to.
• Class TPI FS 240 The second layer must be constructed precisely as described above, perpendicular to the first layer.
• A short-bristled roller can be used for application.

Toilet

• Clean equipment and tools immediately after use. Once the paint has hardened, it can only be removed by mechanical means.
• Toilet TPI FS 240 Spills must be cleaned up immediately using specialized brushes, mechanical methods, wet methods, scrubbing, vacuum cleaning techniques, appropriate detergents, and wax.

IMPORTANT NOTE

• Construction is not permitted. TPI FS 240 Up onto the surface where the moisture content increases.
• Do not replace the liner with another product.
• TPI FS 240 Newly constructed buildings must be protected from moisture, condensation, and water for a minimum of 24 hours.
• The primer will help prevent surface blistering during application.

HEALTH AND SAFETY INFORMATION

Occupational safety and health: Appropriate personal protective equipment, including safety glasses and gloves, should be worn when using this product. It may cause allergic reactions upon contact with eyes, skin, or mucous membranes.

Ecology: Do not dispose of into water sources or soil.

Transport: Not dangerous.

Refer to the product's Material Safety Data Sheet (MSDS) and other relevant safety data sheets.